Created and Sold by Robin Ann Meyer
Untamed Ceiling Drum - Flush Mounts
Free Shipping
Price from $161 to $184
Creation: 2 weeks
Shipping: UPS 2-5 days
$0 Shipping in the US, ask the creator about international shipping.
Estimated Arrival: January 10, 2025
Handmade
Woman Owned
Sustainable
Made In USA
Made To Order
Natural Materials
| Dimensions | Weight |
|---|---|
9H x 12W x 12D in 22.86H x 30.48W x 30.48D cm | |
11H x 16W x 16D in 27.94H x 40.64W x 40.64D cm |
The essence of a wild zebra created with much calmer means. Rice paper soaks india ink organically. There is not way to control the lines as it drinks up the pigment as it pleases.
Assembly & Installation Instructions (Youtube Instructional Video link: https://www.youtube.com/watch?v=kcYu9pbgCjc&t=6s)
Part I: Fixture Assembly:
1. Connect the wires to the socket by feeding them through the connector holes in back of the socket
- the black wire connects to the hot contact (brass colored)
- the white wire connect to the neutral contact (silver colored)
(use a continuity checker to verify the wires are connected to the right pathway)
2. Feed the socket cover through the other end of the wire and connect it to the socket
3. Screw the 1” metal nipple into the socket
4. Run the wire through the drum shade spider ring
5. Next the flush mount goes through the wire. Rest it dish side up on the spider ring
6. Run the star-lock washer through the wire until it sits on the flush mount
7. Secure the socket and the flush mount to the drum shade with the 1/2” nut. Tighten it using your wrench or pliers. It should not be loose.
8. Cut the wire to length. Leave at least 6”
Part II House Install:
9. Secure the bracket to the ceiling can-light using the
two 8/32“ screws
10. Connect the fixture to the house wiring
- the black wire connects to the hot contact
- the white wire connect to the neutral contact
- resecure with the wire nut and electrical tape
(use a continuity checker to verify the wires are connected to the right pathway)
11. Secure the flush mount to the bracket on either side using the two 6/32” screws
12. Screw in the light bulb
13. Peel both sides of the diffuser bottom protection layer off.
14. Feed the diffuser bottom through the drum shade and rest it on the bottom ring. Adjust as needed using the suction cups to pull the diffuser down.
15. Turn on the circuit and ENJOY!
Care Instructions
Dust with a clean dry cloth
Avoid harsh chemicals if cleaning to protect the finish
IMPORTANT: Always turn off at the circuit to the light before installing
Return Policy
Each lamp shade is custom printed and made per order, therefore not allowing me to take returns.
If there are any issues with your purchase please contact me directly. I want you to be happy!
Assembly & Installation Instructions (Youtube Instructional Video link: https://www.youtube.com/watch?v=kcYu9pbgCjc&t=6s)
Part I: Fixture Assembly:
1. Connect the wires to the socket by feeding them through the connector holes in back of the socket
- the black wire connects to the hot contact (brass colored)
- the white wire connect to the neutral contact (silver colored)
(use a continuity checker to verify the wires are connected to the right pathway)
2. Feed the socket cover through the other end of the wire and connect it to the socket
3. Screw the 1” metal nipple into the socket
4. Run the wire through the drum shade spider ring
5. Next the flush mount goes through the wire. Rest it dish side up on the spider ring
6. Run the star-lock washer through the wire until it sits on the flush mount
7. Secure the socket and the flush mount to the drum shade with the 1/2” nut. Tighten it using your wrench or pliers. It should not be loose.
8. Cut the wire to length. Leave at least 6”
Part II House Install:
9. Secure the bracket to the ceiling can-light using the
two 8/32“ screws
10. Connect the fixture to the house wiring
- the black wire connects to the hot contact
- the white wire connect to the neutral contact
- resecure with the wire nut and electrical tape
(use a continuity checker to verify the wires are connected to the right pathway)
11. Secure the flush mount to the bracket on either side using the two 6/32” screws
12. Screw in the light bulb
13. Peel both sides of the diffuser bottom protection layer off.
14. Feed the diffuser bottom through the drum shade and rest it on the bottom ring. Adjust as needed using the suction cups to pull the diffuser down.
15. Turn on the circuit and ENJOY!
Care Instructions
Dust with a clean dry cloth
Avoid harsh chemicals if cleaning to protect the finish
IMPORTANT: Always turn off at the circuit to the light before installing
Return Policy
Each lamp shade is custom printed and made per order, therefore not allowing me to take returns.
If there are any issues with your purchase please contact me directly. I want you to be happy!
Have more questions about this item?